Emergency repair

What to do if your pump station alarm is going off

A high-level alarm means the pumps have not kept up, or have not been told to start. Here is what to do first, what not to do, and when to telephone.

Treat it as urgent, then make the situation safer

A high-level alarm is a warning, not a suggestion. It usually means the water in the chamber has risen past the duty and standby start points. If nothing is done, the next step can be sewage or surface water backing up into a building, a car park or a development road.

Reduce water use if you can: avoid baths, showers, the washing machine and unnecessary flushes, so the chamber has a better chance of not overflowing before an engineer arrives. Keep people away from any flooding, from the open chamber, and from the control panel. Do not enter the wet well, and do not try to run the pumps manually or change panel settings unless you have been shown how to do so safely.

If it is safe to look, note what you can see from outside: whether any pump-running lights are on, whether a breaker has tripped, and whether the alarm has a mute. That information helps, but it is not required before you telephone.

If a station is overflowing now, or a basement or car park is flooding: telephone 01483 355 003 rather than sending the form. That is the general number for quotes, servicing and 24/7 call-outs.
Close-up of a dual-pump control panel fascia, showing pump running, power, pump tripped and red high-level alarm lights, with hand/off/auto and alarm mute switches. The power-on light is illuminated.
A typical dual-pump fascia: running and tripped lights for each pump, a red high-level alarm, hand/off/auto switches and an alarm mute. If it is safe, note what is showing, then telephone. Do not change the switches unless you have been shown how to do so safely.
A white dual-pump control panel with a blue fascia, showing pump running, power, high-level and pump tripped lights, and hand/off/auto and alarm mute switches, mounted on a board beside a small separate alarm unit.
A dual-pump control panel, with the same running, tripped and high-level lights, mounted on a board beside a small separate alarm unit.
A compact Salupo Multi 1 single-pump control and alarm unit on a timber wall, with a red isolator, status lights on the fascia, and a small separate alarm indicator to the right.
A compact single-pump control and alarm unit, of the sort often fitted on a smaller private station. The fascia lights show power, a fault or an alarm.
A grey dual-pump control panel fitted by Southern Pump Services, with a fascia labelled Southern Pump Services Engineering Limited, showing power, high-level, fault reset, running and tripped lights, hand/off/auto switches and an alarm mute.
A dual-pump control panel fitted by Southern Pump Services, with power, high-level and pump-tripped lights, hand/off/auto switches and an alarm mute.

Why the alarm usually sounds

Most call-outs are not a mystery failure of a new pump. The common causes are rag and wipes around the impeller, fats or silt fouling a float, a stuck non-return valve letting water run back into the chamber, a tripped breaker, or a pump that is simply worn out. On many Surrey sites, fine clay and grit add to the wear, and a storm on the Thames, Wey or Mole corridors quickly shows up a chamber that has not been cleaned or a pump that has not been tested.

That is why a one-off silence of the alarm is not always the end of the job. Once the station is stable, it is worth asking whether a planned service and a proper desilt would reduce the chance of a repeat visit.

For the attendance itself — engineers and tankers, day or night, and what happens on a typical call-out — see emergency pump station repair.

An engineer in hi-vis feeding a suction hose into an open brick chamber, with a blue tanker standing behind.
When a station is in alarm, the first job is often to draw the level down so the pumps and floats can be reached safely.

Alarm questions

Should I wait to see if the level drops on its own?

No, particularly on a basement, a car park or a housing development. Telephone 01483 355 003 and reduce water use while you wait. A short delay is often the difference between a wet well that can still be worked in and one that is overflowing.

Will you attend if the station is not on a contract?

Yes. We attend stations of any make, whether or not we installed them and whether or not they are on a maintenance contract. If you have a contract number, have it to hand; it is not required for us to attend.

What should I have ready when I telephone?

The site address, any access or gate codes, and a note of what the panel is showing, if you can read it safely. The make of pump or panel is useful if you know it. If the chamber is already overflowing, say so at the start of the call.