Desilting & jetting

Pump station desilting and jetting in Surrey

Tanker emptying and high-pressure jetting of sewage and surface water wet wells, to take silt, rag and fat off the pumps and the level controls — as a one-off visit, or built into a service contract.

An engineer jetting an open pump station chamber on a rural property, with a yellow and blue tanker parked on the drive.

Why a wet well silts up

In normal operation, grease and oils float and form a mat at the top of the chamber, while grit, sludge and rags settle on the floor. Left alone, that load fouls the floats or the ultrasonic head, starves the pumps, and is one of the most common reasons a sewage pumping station goes into high-level alarm a few weeks after it was last looked at.

On many Surrey sites the problem is worse than a clean textbook wet well would suggest. London Clay and mixed valley soils wash fine material into chambers. Surface water stations on the Wey, Mole and Thames corridors take a lot of grit after heavy rain. Shared stations on blocks and developments collect fats from many kitchens. A chamber that has not been emptied for years is doing extra work before the pumps even start.

Desilting is not a substitute for planned pump station servicing. A service inspects and tests the pumps, valves, controls and alarm. Jetting and a tanker empty the chamber so those parts can actually work. The two jobs complement each other, and are often carried out on the same attendance.

An engineer in hi-vis feeding a suction hose into an open brick pump station chamber, with a blue tanker standing behind.
A suction hose in the chamber and a tanker standing by. Drawing the level down is the first step; jetting then lifts what has settled on the floor and walls.

What a desilting and jetting visit includes

The exact work depends on how full the chamber is and whether we are attending as a planned clean or as part of an emergency call-out. A typical visit follows the same pattern.

  1. Make the site safe and assess the level in the wet well
  2. Draw the chamber down with a tanker where the level is too high to work
  3. High-pressure jet the walls, benching and pipework to lift fat, rag and settled silt
  4. Remove the loosened material from the sump
  5. Clear debris that could foul the pumps or the level controls
  6. Check and clean the floats or the ultrasonic head once they can be reached
  7. Leave the chamber in a condition the pumps can actually work in

If the pumps, valves or panel also need attention, that is a service or a repair, and we will say so clearly rather than only cleaning the well. When a station is already in alarm, the same tanker and jetting work is often the first part of an emergency pump station repair.

How often a pump station should be desilted

On a typical Surrey sewage pumping station the wet well is emptied and jetted once a year, often as part of a 12, 24 or 36 month servicing contract. Busy shared stations, kitchen-heavy sites and surface-water chambers that collect grit after storms may need it more often. A low-use domestic chamber that is already on an annual service may be fine with a desilt on the same visit.

A chamber that has not been desilted in years should be cleaned as a priority, not left until the next planned service date. That is often the most useful first step when someone has inherited a station and has little paperwork for it.

If the high-level alarm is going off now, or the chamber is overflowing, telephone 01483 355 003 rather than booking a planned clean. If the station is still pumping but the wet well is clearly loaded, a planned tanker visit is the right job.

Desilting and jetting across Surrey

The same tanker and jetting work is carried out in Guildford, Woking, Epsom, Reigate and Redhill, Leatherhead and Dorking, Farnham and Camberley, and the towns between them. Floodplain stations and clay sites tend to need it more often; the need for a clean chamber does not change.

We empty and jet stations we maintain under contract and stations we have not seen before, of any make. If you already have a service agreement, desilting can usually be added to it. If you do not, a one-off clean is a straightforward place to start.

Desilting and jetting questions

How often should a pump station be desilted?

On a typical Surrey sewage pumping station the wet well is desilted and jetted once a year, often as part of the service contract. Busy shared stations, kitchen-heavy sites and surface-water chambers that collect grit after storms may need it more often. A chamber that has not been emptied for years should be cleaned as a priority, not left until the next planned service date.

Is desilting the same as a pump station service?

No. A service inspects and tests the pumps, valves, floats and control panel. Desilting and jetting remove the grease mat, rag and settled silt from the chamber so those parts can actually work. The two jobs complement each other and are often carried out on the same attendance, but a service without a clean chamber is only half the work on a neglected station.

Do I need an emergency call-out or a planned desilt?

If the high-level alarm is going off, or the chamber is overflowing, telephone 01483 355 003 for an emergency visit. If the station is still pumping but the wet well is clearly loaded with silt or fat, a planned tanker and jetting visit is the right job, either as a one-off or on a maintenance contract.